DMX512 50W twinkle RGBW LED fiber optic star ceiling kit lights 1000pcs 0.75mm 5m with 28Key RF remote +Crystal
Input voltage:AC86-265V POWER: 50W
COLOR: RGBW LED: RGBW LED
Output gray level: 256 Input Signal: DMX512/1990
Output DMX : 4 channels( RGBW) DMX512 socket standard XLR;
Net Weight: 1.0 KG Gross Weight: 1.8KG
Light body material:Aluminum Remote:28Key RF remote
Remoter dimension: L85× W52 × H7mm Package Size：L300*W200*H14.5mm
Lifetime: 50,000 hours Warranty: 2 years
1x 50w RGBW light engine source
1x 28key RF remote controller
1x 1000pcs 0.75mm 5m end glow fiber optic cable
1 x 5pcs crystal
1x Power adapter
1x User manual
This item have EU/US/UK/AU power plug for choose, we default to delivery EU plug, leave message if you need other plug,thank you!
Attention：Light source unit Occupancy 5 bits address.
The first bit is red light,The second bit is green light,the third bit is blue light ,the fourth bit is white,and the fifth bit is motor speeds(four levels)
Note: FUN = OFF (the tenth code switch up) means to accept DMX512 signal mode
The first DMX address setting:
The decoder set the address bit by coding switch, of which 1-9 is for setting the start address of the Binary numeric code switch of DMX512, the first one is the lowest position, the ninth one is the highest
Bit of address code can be set to 512.
DMX512 start address code is the sum of switches 1-9, at the same time turn downside of the code switch (ON set to "1"), then the value of the bit can be gotten; coding switch up (set to "0"), the value of the bit is 0.
As the following Schematic 1, DMX512 start address is set to 38,
encoding the No. 6,3,2 position on switch dial to "1", others set to "0",
then the sum of the switch 1-9 code value is 32 + 4 + 2,
that is the DMX512 start address 38
As the schematic 2, DMX512 start address is set to 388,
encoding the no. 2,3,6,8 switch dial to "1", others set to "0",
then the sum of the switch 1-8 code value is 4 + 128 + 256 = 388,
that is the DMX512 start address 388.
Note: It will be rf mode when the No. 10 switch is turned down.
Match Code Function (It is available when leave factory)
1.Power on led engine, it works well when red indicated lights.
2.Press the FADE3 and FADE7 at same time in the effective remote distance, the white color of led engine flash. The code matches success.
MODE3:Built-in effects Mode
1:1-4bit is mode 2: 5-6 bit is mode’s speed 3:7-8 bit is motor speed.
Effect choice (button switch No.1 to No.4):12 kinds
1. Push No.1: Seven-color gradual cycle changing. 2.Push No. 2: RGB Fade in and out
3. Push No.1 &2: Severn color jumping 4. Push No.3: RGB jumping.
5. Push No.1 & 3: RGB flash jumping. 6. Push No.2 & 3: Static red
7. Push No. 1 & 2 & 3:Static green 8. Push No.4: Static blue
9. Push No.1 & 4: Static yellow 10. Push No.2 & 4: Static purple
11. Push No.1 & 2 & 3: Static cyan 12. Push No.3 & 4: Static white
Speed Choices (Button Switch No.5 to No. 6) 4 kinds
1. Push No.OFF: 0.5 second. 2.Push No.5: 1 second. 3. Push No.6: 1.5 second. 4. Push No.5,6: 2 second.
Motor Speed Choices (Button Switch No.7 to No. 8) 4 kinds
1.Push No. OFF:motor off. 2. Push No.7:speed 1. 3. Push No.8: speed 2. 4. Push No.7,8: speed 3.
Application Connection Diagram
Maximum fiber connection formula:
Fiber head’s radius: R
Fiber Diameter: D1，D2,D3..........
fiber head’s radius (Diameter 20mm)
fiber head inner diameter ：16-20MM
The number of optical fiber can be installed：
PGConnector inner diameter(MM)
max fiber number
Connection method between Fiber and Led engine:
1.Align all the fiber head, fasten with tapes which can resistance temperature over 130℃
2.Pass through the fiber to connector, fastening rotary tensioner. To make sure the fiber bunch could not move and each fiber must be in the same plane.
3.Cut the fiber bunch to flat surface by heat-knife or blade.
4.Make sure the fiber bunch head is smooth and clean. Thus each fiber’s light will be evenly.
5.Put through the whole fiber connector to fix ring of Led engine. Fasten screw on the top of the fix ring.
Application installation diagram:
1.Make sure the input voltage is correct.
2.Put led engine in the rain or moist place is prohibited
3.Please don’t open led engine for inspection or change the electronic circuits if you are not professionor.
4.Led engine has to be good ventilation, please don’t put at sealed place.
5.Put debris on top of led engine or around it will be caused poor heat dissipation.